**Mixed-Integer Nonlinear **
**Programming Techniques for**
**Process Systems Engineering**
Ignacio E. Grossmann
Department of Chemical Engineering, Carnegie Mellon University
Pittsburgh, PA 15213, USA
January 1999
**ABSTRACT**
This paper has as a major objective to present a unified overview and derivation of mixed-integer nonlinear programming (MINLP) techniques, Branch and Bound, Outer-Approximation, Generalized Benders and Extended Cutting Plane methods, as applied to nonlinear discrete optimization problems that are expressed in algebraic form. The solution of MINLP problems with convex functions is presented first, followed by extensions for the nonconvex case. The solution of logic based representations, known as generalized disjunctive programs, is also described. Finally, numerical comparisons are presented on a small process network problem to provide some insights to confirm the theoretical properties of these methods.
**INTRODUCTION**
Mixed-integer optimization represents a powerful framework for mathematically modeling many optimization problems that involve discrete and continuous variables. Over the last five years there has been a pronounced increase in the development of these models in process systems engineering (see Grossmann et al, 1996; Grossmann, 1996a; Grossmann and Daichendt, 1996; Pinto and Grossmann, 1998; Shah, 1998; Grossmann et al, 1999).
Mixed-integer linear programming (MILP) methods and codes have been available and applied to many practical problems for more than twenty years (e.g. see Nemhauser and Wolsey, 1988). The most common method is the LP-based branch and bound method which has been implemented in powerful codes such as OSL, CPLEX and XPRESS. Recent trends in MILP include the development of branch-and-cut methods such as the lift-and-project method by Balas, Ceria and Cornuejols (1993) in which cutting planes are generated as part of the branch and bound enumeration.
It is not until recently that several new methods and codes are becoming available for mixed-integer nonlinear problems (MINLP) (Grossmann and Kravanja, 1997). In this paper we provide a review the various methods emphasizing a unified treatment for their derivation. As will be shown, the different methods can be derived from three basic NLP subproblems and from one cutting plane MILP problem, which essentially correspond to the basic subproblems of the Outer-Approximation method. Properties of the algorithms are first considered for the case when the nonlinear functions are convex in the discrete and continuous variables. Extensions are then presented for handling nonlinear equations and nonconvexities. Finally, the paper considers properties and algorithms of the recent logic-based representations for discrete/continuous optimization that are known as generalized disjunctive programs. Numerical results on a small example are presented comparing the various algorithms.
**BASIC ELEMENTS OF MINLP METHODS**
The most basic form of an MINLP problem when represented in algebraic form is as follows:
(P1)
where *f(·), g(·) *are *convex, differentiable* functions, *J* is the index set of inequalities, and *x* and *y* are the continuous and discrete variables, respectively. The set *X* is commonly assumed to be a convex compact set, e.g. the discrete set *Y* corresponds to a polyhedral set of integer points, , and in most applications is restricted to 0-1 values, . In most applications of interest the objective and constraint functions *f(·), g(·) *are linear in *y *(e.g. fixed cost charges and logic constraints).
Methods that have addressed the solution of problem (P1) include the branch and bound method (BB) (Gupta and Ravindran, 1985; Nabar and Schrage, 1991; Borchers and Mitchell, 1994; Stubbs and Mehrotra, 1996; Leyffer, 1998), Generalized Benders Decomposition (GBD) (Geoffrion, 1972), Outer-Approximation (OA) (Duran and Grossmann, 1986; Yuan et al., 1988; Fletcher and Leyffer, 1994), LP/NLP based branch and bound (Quesada and Grossmann, 1992), and Extended Cutting Plane Method (ECP) (Westerlund and Pettersson, 1995).
__NLP Subproblems.__ There are three basic NLP subproblems that can be considered for problem (P1):
a) __NLP relaxation__
(NLP1)
where *Y*_{R}* *is the continuous relaxation of the set *Y*, and are index subsets of the integer variables *y*_{i}*,* , which are restricted to lower and upper bounds, at the *k'th** *step of a branch and bound enumeration procedure. It should be noted that *< k, m < k *where are noninteger values at a previous step, and are the floor and ceiling functions, respectively.
Also note that if (NLP1) corresponds to the continuous NLP relaxation of (P1). Except for few and special cases, the solution to this problem yields in general a noninteger vector for the discrete variables. Problem (NLP1) also corresponds to the *k'th* step in a branch and bound search. The optimal objective function provides an absolute lower bound to (P1); for *m *__>__* k*, the bound is only valid for .
b) __NLP subproblem for fixed ____y__^{k}__:__
_{ } _{ }(NLP2)
which yields an upper bound to (P1) provided (NLP2) has a feasible solution. When this is not the case, we consider the next subproblem:
c) __Feasibility subproblem for fixed ____y__^{k}*.*
(NLPF
which can be interpreted as the minimization of the infinity-norm measure of infeasibility of the corresponding NLP subproblem. Note that for an infeasible subproblem the solution of (NLPF) yields a strictly positive value of the scalar variable u.
**Fig. 1. Geometrical interpretation of linearizations in master problem (M-MIP)**
__MILP cutting plane.__ The convexity of the nonlinear functions is exploited by replacing them with supporting hyperplanes derived at the solution of the NLP subproblems. In particular, the new values *y*^{K} (or (*x*^{K}*, y*^{K})) are obtained from a cutting plane MILP problem that is based on the *K* points, (*x*^{k}*, y*^{k}), *k=1...K* generated at the *K* previous steps:
(M-MIP)
where *J*^{k}***J.* When only a subset of linearizations is included, these commonly correspond to violated constraints in problem (P1). Alternatively, it is possible to include all linearizations in (M-MIP). The solution of (M-MIP) yields a valid lower bound to problem (P1). This bound is nondecreasing with the number of linearization points *K*. Note that since the functions *f(x,y)* and *g(x,y)* are convex, the linearizations in (M-MIP) correspond to outer-approximations of the nonlinear feasible region in problem (P1). A geometrical interpretation is shown in Fig.1, where it can be seen that the convex objective function is being underestimated, and the convex feasible region overestimated with these linearizations.
**Algorithms.** The different methods can be classified according to their use of the subproblems (NLP1), (NLP2) and (NLPF), and the specific specialization of the MILP problem (M-MIP) as seen in Fig. 2. It should be noted that in the GBD and OA methods (case (b)), and in the LP/NLP based branch and bound mehod (case (d)), the problem (NLPF) is solved if infeasible subproblems are found. Each of the methods is explained next in terms of the basic subproblems.
** Fig. 2. Major Steps In the Different Algorithms**
**I. Branch and Bound**. While the earlier work in branch and bound (BB) was mostly aimed at linear problems (Dakin, 1965; Garfinkel and Nemhauser, 1972; Taha, 1975), more recently it has also concentrated in nonlinear problems (Gupta and Ravindran, 1985; Nabar and Schrage, 1991; Borchers and Mitchell, 1994; Stubbs and Mehrotra, 1996; Leyffer, 1998). The BB method starts by solving first the continuous NLP relaxation. If all discrete variables take integer values the search is stopped. Otherwise, a tree search is performed in the space of the integer variables . These are successively fixed at the corresponding nodes of the tree, giving rise to relaxed NLP subproblems of the form (NLP1) which yield lower bounds for the subproblems in the descendant nodes. Fathoming of nodes occurs when the lower bound exceeds the current upper bound, when the subproblem is infeasible or when all integer variables y_{i} take on discrete values. The latter yields an upper bound to the original problem.
The BB method is generally only attractive if the NLP subproblems are relatively inexpensive to solve, or when only few of them need to be solved. This could be either because of the low dimensionality of the discrete variables, or because the integrality gap of the continuous NLP relaxation of (P1) is small.
**II. Outer-Approximation** (Duran and Grossmann, 1986; Yuan et al., 1988; Fletcher and Leyffer, 1994). The OA method arises when NLP subproblems (NLP2) and MILP master problems (M-MIP) with *J*^{k}* = J *are solved successively in a cycle of iterations to generate the points *(x*^{k}*, y*^{k}*)*. For its derivation, the OA algorithm is based on the following theorem (Duran and Grossmann, 1986):
**Theorem 1.** Problem (P) and the following MILP master problem (M-OA) have the same optimal solution (x*, y*),
(M-OA)
where K*={*k* for all feasible*y*^{k}***Y,* *x*^{k, }*y*^{k}) is the optimal solution to the problem (NLP2)}.
Since the master problem (M-OA) requires the solution of all feasible discrete variables *y*^{k}, the following MILP relaxation is considered, assuming that the solution of K NLP subproblems is available:
(RM-OA)
Given the assumption on convexity of the functions *f(x,y)* and *g(x,y), *the following property can be easily be established,
**Property 1**. The solution of problem (RM-OA),, corresponds to a lower bound of the solution of problem (P1).
Note that this property can be verified from Fig. 1. Also, since function linearizations are accumulated as iterations proceed, the master problems (RM-OA) yield a non-decreasing sequence of lower bounds, , since linearizations are accumulated as iterations k proceed.
The OA algorithm as proposed by Duran and Grossmann (1986) consists of performing a cycle of major iterations, k=1,..K, in which (NLP1) is solved for the corresponding *y*^{k}, and the relaxed MILP master problem (RM-OA) is updated and solved with the corresponding function linearizations at the point (*x*^{k}*,y*^{k}), for which the corresponding subproblem NLP2 is solved. If feasible, the solution to that problem is used to construct the first MILP master problem; otherwise a feasibility problem (NLPF) is solved to generate the corresponding continuous point. The initial MILP master problem (RM-OA) then generates a new vector of discrete variables. The (NLP2) subproblems yield an upper bound that is used to define the best current solution, . The cycle of iterations is continued until this upper bound and the lower bound of the relaxed master problem,, are within a specified tolerance.
The OA method generally requires relatively few cycles or major iterations. One reason for this behavior is given by the following property:
**Property 2.** *The OA algorithm trivially converges in one iteration if f(x,y) and g(x,y) are linear. *
The proof simply follows from the fact that if *f(x,y)* and *g(x,y)* are linear in *x* and *y* the MILP master problem (RM-OA) is identical to the original problem (P1).
11
It is also important to note that the MILP master problem need not be solved to optimality. In fact given the upper bound *UB*^{K} and a tolerance ** it is sufficient to generate the new *(*y^{K}*, x*^{K}*) *by solving,
(RM-OAF)
While in (RM-OA) the interpretation of the new point *y*^{K}^{ }is that it represents the best integer solution to the approximating master problem, in (RM-OAF) it represents an integer solution whose lower bounding objective does not exceed the current upper bound, *UB*^{K}; in other words it is a feasible solution to (RM-OA) with an objective below the current estimate. Note that in this case the OA iterations are terminated when (RM-OAF) is infeasible.
**III. Generalized Benders Decomposition** (Geoffrion, 1972). The GBD method (see Flippo and Kan 1993) is similar in nature to the Outer-Approximation method. The difference arises in the definition of the MILP master problem (M-MIP). In the GBD method only active inequalities are considered *J*^{k}* = *{*j *|*g*_{j}* *(*x*^{k}*, y*^{k})* = *0} and the set is disregarded. In particular, assume an outer-approximation given at a given point (*x*^{k}*, y*^{k}),
(OA^{k})
where for a fixed *y*^{k} the point *x*^{k} corresponds to the optimal solution to problem (NLP2). Making use of the Karush-Kuhn-Tucker conditions and eliminating the continuous variables *x*, the inequalities in (OA^{k}) can be reduced as follows (Quesada and Grossmann (1992):
(LC^{k})
which is the Lagrangian cut projected in the *y-*space. This can be interpreted as a surrogate constraint of the equations in (OA^{k}), because it is obtained as a linear combination of these.
For the case when there is no feasible solution to problem (NLP2), if the point *x*^{k} is obtained from the feasibility subproblem (NLPFthe following feasibility cut projected in *y* can be obtained using a similar procedure,
(FC^{k})
In this way, the problem (M-MIP) reduces to a problem projected in the *y*-space:
(RM-GBD)
where *KFS* is the set of feasible subproblems (NLP2) and *KIS* the set of infeasible subproblems whose solution is given by (NLPF). Also |*KFS KIS *| *= K*. Since the master problem (RM-GBD) can be derived from the master problem (RM-OA), in the context of problem (P1), Generalized Benders decomposition can be regarded as a particular case of the Outer-Approximation algorithm. In fact the following property, holds between the two methods (Duran and Grossmann, 1986):
**Property 3 ** Given the same set of K subproblems, the lower bound predicted by the relaxed master problem (RM-OA) is greater or equal to the one predicted by the relaxed master problem (RM-GBD).
The above proof follows from the fact that the Lagrangian and feasibility cuts, (LC^{k}) and (FC^{k}), are surrogates of the outer-approximations (OA^{k}). Given the fact that the lower bounds of GBD are generally weaker, this method commonly requires a larger number of cycles or major iterations. As the number of 0-1 variables increases this difference becomes more pronounced. This is to be expected since only one new cut is generated per iteration. Therefore, user-supplied constraints must often be added to the master problem to strengthen the bounds. As for the OA algorithm, the trade-off is that while it generally predicts stronger lower bounds than GBD, the computational cost for solving the master problem (M-OA) is greater since the number of constraints added per iteration is equal to the number of nonlinear constraints plus the nonlinear objective.
The following convergence property applies to the GBD method (Sahinidis and Grossmann, 1991):
**Property 4. ** If problem (P1) has zero integrality gap, the GBD algorithm converges in one iteration once the optimal (x^{*}, y^{*}) is found.
The above property implies that the only case one can expect the GBD method to terminate in one iteration, is when the initial discrete vector is the optimum, and when the objective value of the NLP relaxation of problem (P1) is the same as the objective of the optimal mixed-integer solution. Given the relationship of GBD with the OA algorithm, Property 4 is also inherited by the OA method.
One further property that relates the OA and GBD algorithms is the following (Turkay and Grossmann, 1996):
**Property 5. ** The cut obtained from performing one Benders iteration on the MILP master (RM-OA) is equivalent to the cut obtained from the GBD algorithm.
By making use of this property, instead of solving the MILP (RM-OA) to optimality, for instance by LP-based branch and bound, one can generate a GBD cut by simply performing one Benders (1962) iteration on the MILP. This property will prove to be useful when deriving a logic-based version of the GBD algorithm as will be discussed later in the paper.
**IV.** **Extended Cutting Plane** (Westerlund and Pettersson, 1995). The ECP method, which is an extension of Kelly's cutting plane algorithm for convex NLP (Kelley, 1960), does not rely on the use of NLP subproblems and algorithms. It relies only on the iterative solution of the problem (M-MIP) by successively adding a linearization of the most violated constraint at the predicted point : Convergence is achieved when the maximum constraint violation lies within the specified tolerance. The optimal objective value of (M-MIP) yields a non-decreasing sequence of lower bounds. It is of course also possible to either add to (M-MIP) linearizatons of all the violated constraints in the set *J*^{k} , or linearizations of all the nonlinear constraints *j **** J.*
Note that since the discrete and continuous variables are converged simultaneously, the ECP method may require a large number of iterations. Also, the objective must be defined as a linear function which can easily be accomplished by introducing a new variable to transfer nonlinearities in the objective as an inequality.
**V.** **LP/NLP based Branch and Bound** (Quesada and Grossmann, 1992). This method avoids the complete solution of the MILP master problem (M-OA) at each major iteration. The method starts by solving an initial NLP subproblem which is linearized as in (M-OA). The basic idea consists then of performing an LP-based branch and bound method for (M-OA) in which NLP subproblems (NLP2) are solved at those nodes in which feasible integer solutions are found. By updating the representation of the master problem in the current open nodes of the tree with the addition of the corresponding linearizations, the need of restarting the tree search is avoided.
This method can also be applied to the GBD and ECP methods. The LP/NLP method commonly reduces quite significantly the number of nodes to be enumerated. The trade-off, however, is that the number of NLP subproblems may increase. Computational experience has indicated that often the number of NLP subproblem remains unchanged. Therefore, this method is better suited for problems in which the bottleneck corresponds to the solution of the MILP master problem. Leyffer (1993) has reported substantial savings with this method.
**EXTENSIONS OF MINLP METHODS**
In this section we present an overview of some of the major extensions of the methods presented in the previous section.
**Quadratic Master Problems**. For most problems of interest, problem (P1) is linear in *y*: *f(x,y) = ****(x) + c*^{T}*y, g(x,y) = h(x) + By.* When this is not the case Fletcher and Leyffer (1994) suggested to include a quadratic approximation to (RM-OAF) of the form:
(M-MIQP)
where is the Hessian of the Lagrangian of the last NLP subproblem. Note that *Z*^{K} does not predict valid lower bounds in this case. As noted by Ding-Mei and Sargent (1992), who developed a master problem similar to M-MIQP, the quadratic approximations can help to reduce the number of major iterations since an improved representation of the continuous space is obtained. Note also that for convex *f(x, y)* and *g(x,y)* using (M-MIQP) leads to rigorous solutions since the outer-approximations remain valid. Also, if the function f(x,y) is nonlinear in y, and y is a general integer variable, Fletcher and Leyffer (1994) have shown that the original OA algorithm may require a much larger number of iterations to converge than when the master problem (M-MIQP) is used. This, however, comes at the price of having to solve an MIQP instead of an MILP. Of course, the ideal situation is the case when the original problem (P1) is quadratic in the objective function and linear in the constraints, as then (M-MIQP) is an exact representation of such a mixed-integer quadratic program.
Download
**Share with your friends:** |